DOWNLOAD THE USER MANUAL

Please open and download the PDF below to access the user guide.

IMPORTANT:

Before first use, remove the plastic wrap from the new filter.

◉ Flip the unit over – locate the filter compartment at the base.
◉ Remove the base cover: hold the cover handle and pull straight out to release it.
◉ Remove the plastic wrap from the new filter.
◉ Insert the filter into the compartment.
◉ Reattach the base cover until you hear a “click” confirming it’s securely locked.

Place the unit at least 15 inches (38 cm) away from walls or furniture.

👉 This ensures proper airflow and helps your purifier work at its best.

Plug the power cord into a wall socket.

◉ Press the Power icon to switch on the unit.

The indicator light will turn on, confirming the unit is ready to use.

👉 EDEN starts at Fan Speed 1. While it stays plugged in, it remembers the last speed you used.

IMPORTANT: 

EDEN starts at Fan Speed 1. While it stays plugged in, it remembers the last speed you used.

◉ Power on the purifier.

◉ Press the Fan Speed icon on the control panel.

◉ Each press cycles through the three speeds: 1 → 2 → 3. For Auto, press the Auto Mode icon.

◉ Stop at your preferred speed — the indicator light will confirm the selection.

IMPORTANT: 

In Auto Mode, EDEN reads the air quality and sets the fan speed for you.

Press the Auto Mode icon to activate automatic fan speed control.

The purifier will adjust fan speed based on detected air quality:
🔵 Blue Light → Good air quality (Fan Speed 1)
🟠 Orange Light → Moderate air quality (Fan Speed 2)
🔴 Red Light → Poor air quality (Fan Speed 3)

IMPORTANT: 

Turbo Mode is ideal for use after cooking or whenever the room feels smoky or stuffy.

Press the Turbo Mode icon to activate rapid, high-speed air purification.

IMPORTANT: 

 When Sleep Mode is activated, the purifier runs quietly and the display lights will dim, creating a more restful environment.

Press the Sleep icon to activate.

To exit Sleep Mode, press any button (except Filter or Power).

IMPORTANT: 

To cancel the timer, press the Timer button until the indicator light on the Timer icon turns off, or simply turn off the purifier manually.

Press the Timer icon on the control panel.

Each press cycles through the available durations (2h → 4h → 8h).

Stop at your preferred duration — the indicator light on the Timer icon confirms your selection.

IMPORTANT: 

When Lock Mode is activated, all control buttons are disabled.

Press and hold the Lock icon for 3 seconds.
👉 Recommended for homes with children to prevent accidental operation.

To turn off Lock Mode, press and hold the Lock icon for 3 seconds.
👉 The controls will unlock and return to normal operation.

IMPORTANT: 

Make sure the power plug is firmly inserted into a working wall socket.

Check the plug for visible damage such as cracks, bent pins, or a loose fit.

ADVICE

If your air purifier still doesn’t power on after following the steps above, please contact our support team at www.strongcore.sg/contact

IMPORTANT: 

Do a visual inspection of the unit. If you see dirt or any visible blockage, clean or replace the filter as needed.

Switch off the unit and unplug it from the outlet.

Open the filter compartment.

Remove the filter and inspect it for dirt or blockages.

Clean or replace the filter as needed. (Do not wash the HEPA filter with water.)

ADVICE

If you’re still experiencing unusual noise after following the steps above, please contact our support team at www.strongcore.sg/contact

IMPORTANT:

Before first use, remove the plastic wrap from the new filter.

◉ Press the Fan Speed icon on the control panel.

◉ Each press cycles through the available speeds (1 → 2 → 3).

◉ Stop at your preferred speed — the indicator light will confirm the selection.

Place the unit at least 15 inches (38 cm) away from walls or furniture.

👉 This ensures proper airflow and helps your purifier work at its best.

ADVICE

If airflow is still reduced after completing the steps above, please contact our support team at www.strongcore.sg/contact

IMPORTANT: 

The Strongcore EDEN Air Purifier is best used in rooms up to 800 sq ft (74 m²) with ceilings up to 2.4 m.

👉 Please ensure your room size does not exceed this capacity for optimal purification performance.

Inspect the air outlet on top and the air-inlet holes around the lower body for any visible blockages.

👉 Clean if needed to ensure proper airflow.

For best performance, replace the old HEPA 13 filter with a new one every 6–8 months (depending on usage and air quality).

ADVICE

If air purification still feels poor after completing the steps above, please contact our support team at www.strongcore.sg/contact

IMPORTANT: 

Avoid washing the filter with water or liquids, as this could damage the unit.

🧹 Clean the Pre-Filter (every 2 weeks)

1. Power off & unplug the purifier.
2. Turn it over, pull out the base cover by its handle and take out the filter. The pre-filter is the filter’s outer layer, not a separate part.
3. Vacuum gently using a nozzle attachment or use a soft multi-purpose brush to lift off dust, hair, and debris from the filter’s outer surface and the inside of the base cover. Do not wash the filter.
4. Refit the filter and push the base cover back on until it clicks.

IMPORTANT: 

 For best performance, replace the HEPA 13 filter every 6–8 months (depending on usage and air quality), or whenever the filter reset light turns on.

Flip the unit over to locate the filter compartment at the base.

Remove the base cover: hold the cover handle and pull straight out to release it.

◉ Remove the old filter and insert the new one.

Reattach the base cover until you hear a “click” confirming it’s securely locked.

Replacement may be required sooner depending on usage, especially if you notice any of the following:

Increased operating noise

Reduced airflow

Visible filter clogging

Unpleasant odours

IMPORTANT: 

The Filter Reset function is based on usage hours and internal sensor tracking. Resetting it after each replacement ensures the purifier can accurately monitor filter life and notify you when it’s time to replace the filter under normal operating conditions.

Power ON the air purifier after installing the new filter.

◉ Press and hold the Filter Reset icon for 3 seconds.

◉ Release — the filter indicator turns off, confirming the reset is complete.